If you are a proud owner of an Acura Integra and want to add a touch of style and performance to your vehicle, the Integra Mugen Wing Gen 2 is a perfect choice. This aftermarket wing not only enhances the aerodynamics of your car but also gives it a sporty and aggressive look. In this step-by-step installation guide, we will walk you through the process of installing the Integra Mugen Wing Gen 2 on your Acura Integra. Maxim Works 4-2-1 Stainless Steel header For: B-Series It retails new for $1,300 at ICB No dents
Tools and Materials Needed
Before you begin the installation process, make sure you have the following tools and materials ready:
Integra Mugen Wing Gen 2
Measuring tape
Masking tape
Drill
Drill bits
Screwdriver
Socket set
Ratchet
Level
Marker
Center punch
Silicone adhesive
Cleaning solution
Microfiber cloth
Step 1: Preparing the Wing
Start by unpacking the Integra Mugen Wing Gen 2 and ensuring that all the necessary components are included. Carefully inspect the wing for any defects or damages. If everything looks good, proceed to clean the wing using a cleaning solution and a microfiber cloth. This will remove any dirt or residue and provide a clean surface for installation. 1994-2001 Acura Ingtegra DC2 Type R Jasma MUGEN Muffler in stock!
Step 2: Determining the Mounting Location
Next, you need to determine the optimal mounting location for the wing on your Acura Integra. Measure the width of the trunk and mark the centerline using a marker and masking tape. This will help you align the wing properly later on. Mugen Air intake for 94-01 Integra DC2
Using the measuring tape, measure the distance from the centerline to the edge of the trunk on both sides. Make sure these measurements are equal to ensure that the wing is centered. Adjust the wing position if necessary.
Step 3: Marking the Mounting Holes
With the wing in the desired position, use a marker to mark the locations of the mounting holes on the trunk. Take your time to ensure accuracy as these markings will guide your drilling later on. It's recommended to use a center punch to create a small indentation at each marked location. This will prevent the drill bit from slipping when drilling. 94-01 Integra 2DR DC2 MUGEN Gen
Step 4: Drilling the Mounting Holes
Now it's time to drill the mounting holes for the Integra Mugen Wing Gen 2. Start by selecting an appropriate drill bit size for the screws provided with the wing. Using a drill, carefully drill through the marked locations on the trunk. Make sure to drill straight and avoid applying excessive force to prevent damaging the trunk. Mugen Gen2 Spoiler (Integra/DC2)
Step 5: Installing the Wing
Once the holes are drilled, attach the Integra Mugen Wing Gen 2 to the trunk using the screws provided. Start by inserting the screws through the pre-drilled holes on the wing and aligning them with the holes on the trunk. Use a screwdriver or a socket set with a ratchet to tighten the screws securely. Double-check the alignment and adjust if necessary. Honda Motocompacto NF10 E-Scooter. 12 miles range at speed up to 15 mph. Weights: 52.414 pounds. Hight: 6.300 inches Width: 25.020 inches Legnth: 35.030 inches
Step 6: Leveling the Wing
To ensure that the wing is level, use a level and place it across the top surface of the wing. Make any necessary adjustments to achieve a level position. Once you are satisfied with the alignment, tighten the screws securely to hold the wing in place. Buy rare Steering wheel Online
Step 7: Applying Silicone Adhesive
To provide additional support and prevent any water leakage, apply a thin layer of silicone adhesive around the base of the wing where it contacts the trunk. This will create a watertight seal and ensure a secure installation. Allow the adhesive to dry according to the manufacturer's instructions before proceeding. Mugen DC2 Type R kit
Step 8: Final Touches
After the silicone adhesive has dried, remove any masking tape or residue from the trunk. Clean the wing and surrounding area using a microfiber cloth to remove any fingerprints or smudges. Step back and admire your newly installed Integra Mugen Wing Gen 2. 1988-2001 Honda Civic EF DC EG EK Obd1 VTECP28- G01 ARU SST Chipped ECU
Conclusion
The installation process for the Integra Mugen Wing Gen 2 may seem daunting at first, but by following this step-by-step guide, you can easily add this stylish and functional accessory to your Acura Integra. Remember to take your time, measure accurately, and ensure a secure installation. Enjoy the enhanced aerodynamics and sporty look that the Integra Mugen Wing Gen 2 brings to your vehicle
Comments